Automatic Mouse

By | 08.02.2019
Automatic Mouse

It makes your mouse move and click automatically on locations that you defined. It can use a small picture to locate a point on the screen, which makes it very flexible. Regardless of where the target is, as long as it can be seen on the screen, the program will be able to find it. Key features:
automatic mouse

Related Apps

Automatic Mouse

Russian version of manual is here. Introduction Automatic mouse switcher consists of two applications written using Qt4 libraries: Background switcher amswitcher. It will pop up notification balloon in tray each time it happens.

There is no tray icon shown except for when balloon pops up. Once you change the settings, they will be propogated to background switcher shortly, usually within 1 minute. You should only run this application when you need to change settings.

If you followed default installation scenario, you should have automatic mouse switcher background process started. It should also be configured to automatically start this process when user logs in, and close it on logoff. You can check whether background process will be automatically started when user logs in, or manually enable or disable it using configuration utility.

Do not forget to press Save each time to want to apply settings. Installation It is generally recommended to accept default settings during whole installation unless you know what you do. Note that if you do not install libraries required, you must ensure that required libraries are available on your computer somewhere else, and that they are in PATH.

Quick walk-through installation process is below: Basic configuration To configure automatic mouse switcher please follow next simple steps: Launch configuration utility – you can find shortcut to configuration utility in your applications menu.

When it is started, you will get the following interface: Interface contains two lists – lists of mouse devices that have speed settings configured, and list of mouse devices that are currently present. Please note small? Add devices into configured list – select existing devices and add them one by one to configured list using Configure existing button. Each device may only be added once. As you add devices, they will appear in configured devices list.

Each device will be configured with current mouse speed settings, and you may adjust it later. If you detach device, it will not be removed from configured devices. If you accidentally add device that should not be configured, you can select it from configured devices list and use Remove configured button. As a rule of thumb, you should add devices that you are going to use as mouse devices. There is always Default mouse device present in configured devices list. Arrange devices priority – when background switcher detects new device, it will look through list of devices from top to bottom and will select the first configured device present.

You can arrange configured device by priority by by selecting one and moving it Up and Down with buttons. As a rule of thumb, you should put devices that you are unplugging first. In this case Bluetooth mouse’s settings will be used when mouse is plugged, and Touchpad settings when mouse is unplugged. Note that Default mouse is always the last device.

It will be used if no other devices present. Configure mouse settings for each device – use Go to mouse config button to open mouse configuration settings. It will open system mouse settings windows where you can adjust mouse speed and try it out immediately. Once you feel that speed is exactly what you need for specific device, use Apply or OK button to adjust system settings.

Once mouse speed settings are applied to system, you can assign them to selected configured device by pressing Use current config button. Note that Use current config button remembers active system mouse speed settings for selected device. You should always apply configured settings to system before remembering them for device. Assign friendly names – some devices might not have friendly names, and you may rename any of configured devices by double clicking their names.

It is advised to do so when system-reported name does not explain the nature of device. The name you have assigned will shown in popup balloon when settings are changed by background switcher. Note that only configured devices list is affected – same device in existing devices list will keep system-reported name. This is “by design”. You can match configured and existing devices by their IDs. Save or discard changes – no changes are applied or saved unless you press Save button.

Once you’ve done with settings, you should press Save button which will propogate settings to background switcher and will overwrite previous settings.

If you want to close configuration without applying settings you should choose Close button. If you want to discard all the changes you have done and also force existing devices list refresh, use Refresh button. Since existing devices are refreshed automatically, you dont have to use this button. Try it out – once you’ve done with settings, you should wait approximately one minute for settings to propogate to background switcher.

Each time background switcher detects new device it will look for the first configured device that exists, otherwise it will use Default mouse.

When settings are changed, a notification balloon with configured device name will be shown. Configuration is kept in registry for each user separately. Advanced settings In addition to configuration described above, you can modify some parameters via registry. Such changes might require you to restart background switcher. BalloonHideTimeout [DWORD] – time to enforce balloon hide after it was shown sometimes Windows does not hide balloon as it should, and removal must be enforced , in ms.

If it does not appear in this time, icon and balloon is removed. This occurs if there is another balloon stuck at tray. When you enable Bluetooth controller, it creates dozen of devices at once and it makes sense to wait for all devices to be created. It is ms by default and should be small enough not to cause any problems, but should still fight offflickering effects. Lowering it will slightly increase CPU load, but improve delay between configuration changes and their usage.

Introduction

But an app that helps you automate some of those things could provide welcome relief. Automatic Mouse and Keyboard has lots of options to. Free Mouse Clicker app to auto click your mouse. Download the Free Mouse Auto Clicker software freeware. Repeat mouse clicks with our free software. Automatic Mouse and Keyboard – Automatic Mouse and Keyboard is a really powerful and easy-to-use Mouse and Keyboard automation tool. It simulate a lot of.

Automatic Mouse Move and Click Software 7.0

Define Click Type, X Co-ordinates, Y-Co-ordinate and specify whether to return mouse cursor back to original location and automate mouse clicks. Download and try Auto Mouse Click for free. The Mouse Click Script can be loaded to run at a later time.

Software Categories

Russian version of manual is here. Introduction Automatic mouse switcher consists of two applications written using Qt4 libraries:

HOWTO VIDEO: Auto Mouse Click : Automate Left or Right Button Clicks of Mouse

This software offers a solution to users who want to automatically move the mouse pointer to a specific screen location and perform an action. Auto clicker is a mouse automation clicker at specified Mouse Location. The list includes Free Auto Clicker, GS Auto Clicker, Perfect Automation Clicker, Auto. Free Mouse Clicker app to auto click your mouse. Download the Free Mouse Auto Clicker software freeware. Repeat mouse clicks with our free software.

Automatic Mouse

Leave a Reply

Your email address will not be published. Required fields are marked *